Free Shipping on orders over US$75 all over the World How do we deliver your item ?

Top 2 Cell Phone Jammer Circuits

Introduction

A Cell Phone Jammer Circuit or a Mobile Jammer Circuit is an instrument or gadget that can forestall the gathering of signs by Mobile Phones. Essentially, a Mobile Jammer Circuit is a RF Transmitter, which broadcasts Radio Signals in something very similar (or comparative) frequency range of the GSM Communication.

WARNING: Blocking or Jamming Radio Signals is illegal in most countries. Check your local laws before using such devices.

In this project, I have designed two Mobile Jammer Circuits, where the first one is using a 555 Timer IC and the other one is built using active and passive components.  

Circuit 1: Simple Mobile Jammer Circuit Diagram

Top 2 Cell Phone Jammer Circuits
Top 2 Cell Phone Jammer Circuits

Cell Phone Jammer Circuit Explanation

If you understand the above circuit, this circuit analysis is simple and easy. For any jammer circuit, remember that there are three main important circuits. When they are combined together, the output of that circuit will work as a jammer. The three circuits are

  • RF amplifier.
  • Voltage controlled oscillator.
  • Tuning circuit.

So the transistor Q1, capacitors C4 & C5 and resistor R1 constitute the RF amplifier circuit. This will amplify the signal generated by the tuned circuit. The amplification signal is given to the antenna through C6 capacitor. Capacitor C6 will remove the DC and allow only the AC signal which is transmitted in the air.

When the transistor Q1 is turned ON, the tuned circuit at the collector will get turned ON. The tuned circuit consists of capacitor C1 and inductor L1. This tuned circuit will act as an oscillator with zero resistance.

This oscillator or tuned circuit will produce the very high frequency with minimum damping. The both inductor and capacitor of tuned circuit will oscillate at its resonating frequency.

The tuned circuit operation is very simple and easy to understand. When the circuit gets ON, the voltage is stored by the capacitor according to its capacity. The main function of capacitor is to store electric energy. Once the capacitor is completely charged, it will allow the charge to flow through inductor. We know that inductor is used to store magnetic energy. When the current is flowing across the inductor, it will store the magnetic energy by this voltage across the capacitor and will get decreased, at some point complete magnetic energy is stored by inductor and the charge or voltage across the capacitor will be zero.

The magnetic charge through the inductor will decreased and the current will charge the capacitor in opposite or reverse polarity manner. Again after some period of time, capacitor will get completely charged and magnetic energy across the inductor will be completely zero. Again the capacitor will give charge to the inductor and becomes zero. After some time, inductor will give charge to capacitor and become zero and they will oscillate and generate the frequency.

This circle run upto the internal resistance is generated and oscillations will get stop. RF amplifier feed is given through the capacitor C5 to the collector terminal before C6 for gain or like a boost signal to the tuned circuit signal. The capacitors C2 and C3 are used for generating the noise for the frequency generated by the tuned circuit. Capacitors C2 and C3 will generate the electronic pulses in some random fashion (technically called noise).

The feedback back or boost given by the RF amplifier, frequency generated by the tuned circuit, the noise signal generated by the capacitors C2 and C3 will be combined, amplified and transmitted to the air.

Cell phone works at the frequency of 450 MHz frequency. To block this 450MHz frequency, we also need to generate 450Mhz frequency with some noise which will act as simple blocking signal, because cell phone receiver will not be able to understand to which signal it has been received. By this, we can able to block the cell phone signal from reaching the cell phones.

So here in the above circuit, we generated the 450 MHz frequency to block the actual cell phone signal. That’s what the above circuit will act as a jammer for blocking the actual signal.

Circuit 2: Mobile Jammer Circuit using 555

Top 2 Cell Phone Jammer Circuits
Components Required:
555 Timer IC
Resistors – 220Ω x 2, 5.6KΩ, 6.8KΩ, 10KΩ, 82KΩ
Capacitors – 2pF, 3.3pF, 4.7pF, 47pF, 0.1µF, 4.7µF, 47µF
30pF Trimmer Capacitor
LED
Coils 3 Turn 24 AWG, 4 Turn 24 AWG
Antenna 15 Turn 24 AWG
BF495 Transistor
ON / OFF Switch
9V Battery

Operation:
After building this circuit on a perf board and supplying power to it, I have placed a mobile phone near the circuit (I am yet to turn on the switch). Before turning on the power, my mobile phone was able to capture majority of the signals as it is displaying full bars.
Once I turned on the circuit, the signal bars on the phone started to reduce and finally it stopped at a single bar.
So, in conclusion, I can say that this circuit blocks the signals but cannot completely jam them.

Source: Electronichub

Tags:

We will be happy to hear your thoughts

Leave a reply

TronikShop - Buy Online Electronic Components & Consumer Electronics
Logo
Reset Password
Shopping cart